User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            B&K 4011: 5 MHz Function Generator
DATE:                  06-Aug-97
AUTHOR:                User Contributed
REVISION:
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       42
NUMBER OF LINES:       476
CONFIGURATION:         HP 5335A
CONFIGURATION:         HP 34401A
STANDARD:              Fluke A55
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-   R     N              P             M              F        W
  1.002  ASK+                                          X
  1.003  STD          Fluke A55
  1.004  IEEE         [@5335][TERM LF]
  1.005  IEEE         [@535]IN;
  1.006  HEAD         INITIAL CONDITIONS
  1.007  DISP         Set the UUT as follows:
  1.007  DISP         RANGE  5
  1.007  DISP         function  sine
  1.007  DISP         OUTPUT LEVEL  full ccw
  1.007  DISP         DUTY CYCLE  OFF
  1.007  DISP         CMOS LEVEL  OFF
  1.008  DISP         Set the UUT as follows:
  1.008  DISP         DC OFFSET  OFF
  1.008  DISP         -20 db  OFF
  1.008  DISP         FREQUNCY COARSE/FINE  full ccw
  1.009  HEAD         {}
  1.010  HEAD         {* Frequency Accuracy *}
  1.011  JMP          2.001
  1.012  EVAL
  2.001  DISP         Connect the UUT OUTPUT BNC via a 50 ohm feedthrough
  2.001  DISP         termination to INPUT A on the 5335A counter.
  2.002  DISP         Set the UUT output level control midway.
  2.003  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
  2.003  DISP         of 000.5 Hz.
  2.004  IEEE         [@5335]FU1,AX1,AU1;
  2.005  IEEE         [@5335][I]
  2.006  IEEE         [@5335][T0][I]
  2.007  ACC          .500H          0.0010%
  2.008  MEME
  2.009  MEMC         H              0.1000U
#!          Test Tol 0.1, Sys Tol 5e-006, TUR 20000.000 (>= 4.00).
  3.001  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
  3.001  DISP         of 005.0 Hz.
  3.002  IEEE         [@5335][T0][I]
  3.003  ACC          5.000H         0.0010%
  3.004  MEME
  3.005  MEMC         H              0.10005U
#!          Test Tol 0.10005, Sys Tol 5e-005, TUR 2001.000 (>= 4.00).
  4.001  DISP         Set the UUT frequency RANGE to 50.
  4.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
  4.002  DISP         of 0005 Hz.
  4.003  IEEE         [@5335][T0][I]
  4.004  ACC          5.000H         0.0010%
  4.005  MEME
  4.006  MEMC         H              1.00005U
#!          Test Tol 0.10005, Sys Tol 5e-005, TUR 2001.000 (>= 4.00).
  5.001  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
  5.001  DISP         of 0050 Hz.
  5.002  IEEE         [@5335][T0][I]
  5.003  ACC          50.000H        0.0010%
  5.004  MEME
  5.005  MEMC         H              1.0005U
#!          Test Tol 1.0005, Sys Tol 0.0005, TUR 2001.000 (>= 4.00).
  6.001  DISP         Set the UUT frequency RANGE to 500.
  6.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
  6.002  DISP         of 0050 Hz.
  6.003  IEEE         [@5335][T0][I]
  6.004  ACC          50.000H        0.0010%
  6.005  MEME
  6.006  MEMC         H              1.0005U
#!          Test Tol 1.0005, Sys Tol 0.0005, TUR 2001.000 (>= 4.00).
  7.001  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
  7.001  DISP         of 0500 Hz.
  7.002  IEEE         [@5335][T0][I]
  7.003  ACC          500.00H        0.0010%
  7.004  MEME
  7.005  MEMC         H              1.005U
#!          Test Tol 1.005, Sys Tol 0.005, TUR 201.000 (>= 4.00).
  8.001  DISP         Set the UUT frequency RANGE to 5K.
  8.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
  8.002  DISP         of 0500 Hz.
  8.003  IEEE         [@5335][T0][I]
  8.004  ACC          500.00H        0.0010%
  8.005  MEME
  8.006  MEMC         H              1.005U
#!          Test Tol 1.005, Sys Tol 0.005, TUR 201.000 (>= 4.00).
  9.001  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
  9.001  DISP         of 5000 Hz.
  9.002  IEEE         [@5335][T0][I]
  9.003  ACC          5000.00H       0.0010%
  9.004  MEME
  9.005  MEMC         H              1.05U
#!          Test Tol 1.05, Sys Tol 0.05, TUR 21.000 (>= 4.00).
 10.001  DISP         Set the UUT frequency RANGE to 50K.
 10.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 10.002  DISP         of 05.00 kHz.
 10.003  IEEE         [@5335][T0][I]
 10.004  MEM/         1000
 10.005  ACC          5.000kH        0.0010%
 10.006  MEME
 10.007  MEMC         kH             0.01005U
#!          Test Tol 0.01005, Sys Tol 5e-005, TUR 201.000 (>= 4.00).
 11.001  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 11.001  DISP         of 50.00 kHz.
 11.002  IEEE         [@5335][T0][I]
 11.003  MEM/         1000
 11.004  ACC          50.000kH       0.0010%
 11.005  MEME
 11.006  MEMC         kH             0.0105U
#!          Test Tol 0.0105, Sys Tol 0.0005, TUR 21.000 (>= 4.00).
 12.001  DISP         Set the UUT frequency RANGE to 500K.
 12.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 12.002  DISP         of 050.0 kHz.
 12.003  IEEE         [@5335][T0][I]
 12.004  MEM/         1000
 12.005  ACC          50.000kH       0.0010%
 12.006  MEME
 12.007  MEMC         kH             0.1005U
#!          Test Tol 0.1005, Sys Tol 0.0005, TUR 201.000 (>= 4.00).
 13.001  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 13.001  DISP         of 500.0 kHz.
 13.002  IEEE         [@5335][T0][I]
 13.003  MEM/         1000
 13.004  ACC          500.000kH      0.0010%
 13.005  MEME
 13.006  MEMC         kH             0.105U
#!          Test Tol 0.105, Sys Tol 0.005, TUR 21.000 (>= 4.00).
 14.001  DISP         Set the UUT frequency RANGE to 5M.
 14.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 14.002  DISP         of 0500 kHz.
 14.003  IEEE         [@5335][T0][I]
 14.004  MEM/         1000
 14.005  ACC          500.000kH      0.0010%
 14.006  MEME
 14.007  MEMC         kH             1.005U
#!          Test Tol 1.005, Sys Tol 0.005, TUR 201.000 (>= 4.00).
 15.001  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 15.001  DISP         of 5000 kHz.
 15.002  IEEE         [@5335][T0][I]
 15.003  MEM/         1000
 15.004  ACC          5000.00kH      0.0010%
 15.005  MEME
 15.006  MEMC         kH             1.05U
#!          Test Tol 1.05, Sys Tol 0.05, TUR 21.000 (>= 4.00).
 16.001  DISP         Disconnect all test equipment.
 16.002  HEAD         {}
 16.003  HEAD         {* Output Tests *}
 16.004  JMP          17.001
 16.005  EVAL
 17.001  DISP         Connect the UUT OUTPUT to the DVM. DO NOT use a 50 ohm
 17.001  DISP         termination.
 17.002  DISP         Set the UUT frequency RANGE to 5K.
 17.003  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 17.003  DISP         of 1000 Hz.
 17.004  DISP         Set the UUT output level control full CW.
 17.005  IEEE         [@34401]*RST
 17.006  IEEE         [@34401] MEAS:VOLT:AC?[I]
 17.007  MEM*         2.828
 17.008  MEME                                                     >1
 17.009  MATH         m[1]=m[1]/2
 17.010  ACC    10    20.000Vp-p     0.06% 0.03/
 17.011  MEME
 17.012  MEMC         Vp-p           10.00%        open
#!          Test Tol 20, Sys Tol 0.015, TUR 1333.333 (>= 4.00).
 18.001  DISP         Connect the UUT OUTPUT to the DVM through the 50 ohm
 18.001  DISP         termination.
 18.002  IEEE         [@34401] MEAS:VOLT:AC?[I]
 18.003  MEM*         2.828
 18.004  MEME
 18.005  MEME                                                     <1
 18.006  MEMC         Vp-p           10.00%        term.
#! T.U.R. not calculated because System Uncertainty not available.
 19.001  HEAD         {}
 19.002  HEAD         {* -20dB Test *}
 19.003  IEEE         [@34401]CALC:STAT ON
 19.003  IEEE         [@34401]CALC:FUNC DB
 19.004  IEEE         [@34401]READ?[I]
 19.005  DISP         Set the UUT -20dB attenuator to ON.
 19.006  IEEE         [@34401]READ?[I]
 19.007  ACC          -20.00D        0.001U
 19.008  MEME
 19.009  MEMC         D              1.00U
#!          Test Tol 1, Sys Tol 0.001, TUR 1000.000 (>= 4.00).
 20.001  IEEE         [@34401]CALC:STAT OFF
 20.002  DISP         Disconnect all test equipment.
 20.003  HEAD         {}
 20.004  HEAD         {* DC Offset Test *}
 20.005  IEEE         [@34401]*RST
 20.006  DISP         Connect the UUT OUTPUT to the DVM. Do not use a
 20.006  DISP         termination.
 20.007  DISP         Set the UUT as follows:
 20.007  DISP         OUTPUT LEVEL  midway
 20.007  DISP         -20dB  OFF
 20.007  DISP         DC OFFSET  ON
 20.008  DISP         Rotate the DC OFFSET control fully CCW.
 20.009  IEEE         [@34401]MEAS:VOLT:DC?[I]
 20.010  ACC    10    -10.00V        .0035% .0005/
 20.011  MEME
 20.012  MEMC         V              100.00%
#!          Test Tol 10, Sys Tol 0.0004, TUR 25000.000 (>= 4.00).
 21.001  DISP         Rotate the DC OFFSET control fully CW.
 21.002  IEEE         [@34401]MEAS:VOLT:DC?[I]
 21.003  ACC    10    10.00V         .0035% .0005/
 21.004  MEME
 21.005  MEMC         V              100.00%
#!          Test Tol 10, Sys Tol 0.0004, TUR 25000.000 (>= 4.00).
 22.001  DISP         Set the UUT as follows:
 22.001  DISP         OUTPUT LEVEL  full ccw
 22.001  DISP         DC OFFSET  OFF
 22.002  DISP         Disconnect all test equipment.
 22.003  HEAD         {}
 22.004  HEAD         {* Sine Wave Tests *}
 22.005  HEAD         {* Frequency Response *}
 22.006  HEAD         {Referenced to 1 kHz}
 22.007  HEAD         Sine Wave Tests
 22.008  JMP          23.001
 22.009  EVAL
 23.001  DISP         Set the UUT as follows:
 23.001  DISP         RANGE  5K
 23.001  DISP         FREQUENCY  1000
 23.002  DISP         Connect the UUT OUTPUT BNC to the 34401A input.
 23.003  IEEE         [@34401]CONF:VOLT:AC[GTL]
 23.004  DISP         Adjust the UUT OUTPUT LEVEL control for a 3.00V
 23.004  DISP         on the DMM.
 23.005  IEEE         [@34401]MEAS:VOLT:AC?[I]
 23.006  MEME                                                     >20
 23.007  DISP         Set the UUT 20 dB to ON.
 23.008  DISP         Connect the Fluke A55 Thermal Converter to the
 23.008  DISP         UUT OUTPUT BNC.
 23.009  DISP         Connect the Thermal Converter output to the DVM input.
 23.010  DISP         Set the UUT 20 dB to OFF.
 23.011  HEAD         [27][91]7m[27][91]5mPlease Wait, Measurement in Progress
 23.012  IEEE         [@34401][D3]MEAS:VOLT:DC?[I]
 23.013  HEAD         * Sine Wave Tests *
#23.008  MEM*         1000
 23.014  MEME                                                     >1
 23.015  MATH         m[19] = m[1] / m[20]
 23.016  DISP         Set the UUT as follows:
 23.016  DISP         20 dB  ON
 23.016  DISP         RANGE  5
 23.017  DISP         Set the FREQUENCY controls full CW.
 23.018  DISP         Set the UUT 20 dB to OFF.
 23.019  HEAD         [27][91]7m[27][91]5mPlease Wait, Measurement in Progress
 23.020  IEEE         [@34401][D3]MEAS:VOLT:DC?[I]
 23.021  HEAD         * Sine Wave Tests *
#23.016  MEM*         1000
 23.022  MATH         mem = mem / m[19]
 23.023  MATH         mem = mem - m[20]
 23.024  MEM/         2
 23.025  MATH         mem = mem + m[20]
 23.026  MEME
 23.027  MEME                                                     <20
 23.028  MEMC         V              5.00%         6H
#! T.U.R. not calculated because System Uncertainty not available.
 24.001  DISP         Set the UUT as follows:
 24.001  DISP         20 dB  ON
 24.001  DISP         RANGE  50
 24.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 24.002  DISP         of 0050 Hz.
 24.003  DISP         Set the UUT 20 dB to OFF.
 24.004  HEAD         [27][91]7m[27][91]5mPlease Wait, Measurement in Progress
 24.005  IEEE         [@34401][D3]MEAS:VOLT:DC?[I]
 24.006  HEAD         * Sine Wave Tests *
#24.007  MEM*         1000
 24.007  MATH         mem = mem / m[19]
 24.008  MATH         mem = mem - m[20]
 24.009  MEM/         2
 24.010  MATH         mem = mem + m[20]
 24.011  MEME
 24.012  MEME                                                     <20
 24.013  MEMC         V              5.00%         50H
#! T.U.R. not calculated because System Uncertainty not available.
 25.001  DISP         Set the UUT as follows:
 25.001  DISP         20 dB  ON
 25.001  DISP         RANGE  500
 25.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 25.002  DISP         of 0500 Hz.
 25.003  DISP         Set the UUT 20 dB to OFF.
 25.004  HEAD         [27][91]7m[27][91]5mPlease Wait, Measurement in Progress
 25.005  IEEE         [@34401][D3]MEAS:VOLT:DC?[I]
 25.006  HEAD         * Sine Wave Tests *
#25.007  MEM*         1000
 25.007  MATH         mem = mem / m[19]
 25.008  MATH         mem = mem - m[20]
 25.009  MEM/         2
 25.010  MATH         mem = mem + m[20]
 25.011  MEME
 25.012  MEME                                                     <20
 25.013  MEMC         V              5.00%         500H
#! T.U.R. not calculated because System Uncertainty not available.
 26.001  DISP         Set the UUT as follows:
 26.001  DISP         20 dB  ON
 26.001  DISP         RANGE  5K
 26.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 26.002  DISP         of 5000 Hz.
 26.003  DISP         Set the UUT 20 dB to OFF.
 26.004  HEAD         [27][91]7m[27][91]5mPlease Wait, Measurement in Progress
 26.005  IEEE         [@34401][D30000]MEAS:VOLT:DC?[I]
 26.006  HEAD         * Sine Wave Tests *
#26.007  MEM*         1000
 26.007  MATH         mem = mem / m[19]
 26.008  MATH         mem = mem - m[20]
 26.009  MEM/         2
 26.010  MATH         mem = mem + m[20]
 26.011  MEME
 26.012  MEME                                                     <20
 26.013  MEMC         V              5.00%         5000H
#! T.U.R. not calculated because System Uncertainty not available.
 27.001  DISP         Set the UUT as follows:
 27.001  DISP         20 dB  ON
 27.001  DISP         RANGE  50K
 27.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 27.002  DISP         of 50.00 KHz.
 27.003  DISP         Set the UUT 20 dB to OFF.
 27.004  HEAD         [27][91]7m[27][91]5mPlease Wait, Measurement in Progress
 27.005  IEEE         [@34401][D30000]MEAS:VOLT:DC?[I]
 27.006  HEAD         * Sine Wave Tests *
#27.007  MEM*         1000
 27.007  MATH         mem = mem / m[19]
 27.008  MATH         mem = mem - m[20]
 27.009  MEM/         2
 27.010  MATH         mem = mem + m[20]
 27.011  MEME
 27.012  MEME                                                     <20
 27.013  MEMC         V              5.00%         50kH
#! T.U.R. not calculated because System Uncertainty not available.
 28.001  DISP         Set the UUT as follows:
 28.001  DISP         20 dB  ON
 28.001  DISP         RANGE  500K
 28.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 28.002  DISP         of 500.0 KHz.
 28.003  DISP         Set the UUT 20 dB to OFF.
 28.004  HEAD         [27][91]7m[27][91]5mPlease Wait, Measurement in Progress
 28.005  IEEE         [@34401][D30000]MEAS:VOLT:DC?[I]
 28.006  HEAD         * Sine Wave Tests *
#28.007  MEM*         1000
 28.007  MATH         mem = mem / m[19]
 28.008  MATH         mem = mem - m[20]
 28.009  MEM/         2
 28.010  MATH         mem = mem + m[20]
 28.011  MEME
 28.012  MEME                                                     <20
 28.013  MEMC         V              5.00%         500kH
#! T.U.R. not calculated because System Uncertainty not available.
 29.001  DISP         Set the UUT as follows:
 29.001  DISP         20 dB  ON
 29.001  DISP         RANGE  5M
 29.002  DISP         Adjust the UUT FREQUENCY controls for a UUT readout
 29.002  DISP         of 5000 KHz.
 29.003  DISP         Set the UUT 20 dB to OFF.
 29.004  HEAD         [27][91]7m[27][91]5mPlease Wait, Measurement in Progress
 29.005  IEEE         [@34401][D30000]MEAS:VOLT:DC?[I]
 29.006  HEAD         * Sine Wave Tests *
#29.007  MEM*         1000
 29.007  MATH         mem = mem / m[19]
 29.008  MATH         mem = mem - m[20]
 29.009  MEM/         2
 29.010  MATH         mem = mem + m[20]
 29.011  MEME
 29.012  MEME                                                     <20
 29.013  MEMC         V              5.00%         5000kH
#! T.U.R. not calculated because System Uncertainty not available.
 30.001  DISP         Set the UUT as follows:
 30.001  DISP         20 dB  ON
 30.002  DISP         Set the OUTPUT LEVEL full CCW.
 30.003  DISP         Disconnect all equipment.
 30.004  HEAD         {}
 30.005  HEAD         {* Distortion Test *}
 30.006  JMP          31.001
 30.007  EVAL
 31.001  DISP         Connect the UUT OUTPUT via a 50 ohm termination to the
 31.001  DISP         HIGH INPUT on the 8903A distortion analyzer.
 31.002  DISP         Set the UUT as follows:
 31.002  DISP         RANGE  5K
 31.002  DISP         FREQUENCY  1000
 31.002  DISP         OUTPUT LEVEL  midway
 31.002  DISP         20 dB  OFF
 31.003  IEEE         [@8903]M3
 31.004  IEEE         [@8903]LN
 31.005  IEEE         [@8903][I]
 31.006  ACC          1pct           0.015U
 31.007  MATH         mem1=0
 31.008  MEME
 31.009  MEMC         pct            -1.00U        1000H
#!          Test Tol 1, Sys Tol 0.015, TUR 66.667 (>= 4.00).
 32.001  DISP         Set the UUT OUTPUT LEVEL full CCW.
 32.002  DISP         Disconnect all test equipment.
 32.003  HEAD         {}
 32.004  HEAD         {* Square Wave Tests *}
 32.005  HEAD         {* Symmetry Tests *}
 32.006  HEAD         * Square Wave Tests *
 32.007  JMP          33.001
 32.008  EVAL
 33.001  DISP         Set the UUT as follows:
 33.001  DISP         RANGE  5
 33.001  DISP         FREQUENCY COARSE/FINE  full ccw
 33.001  DISP         function  square
 33.001  DISP         OUTPUT LEVEL  midpoint
 33.002  DISP         Connect the UUT OUTPUT via a 50 ohm termination to
 33.002  DISP         INPUT A on the 5335A counter.
 33.003  IEEE         [@5335]IN;[D2000]
 33.003  IEEE         [@5335]FN12;
 33.004  IEEE         [@5335][T0][I]
 33.005  ACC          50.00percent   0.001U
 33.006  MEME
 33.007  MEMC         percent        2.00U         .5H
#!          Test Tol 2, Sys Tol 0.001, TUR 2000.000 (>= 4.00).
 34.001  DISP         Set the UUT as follows:
 34.001  DISP         RANGE  50
 34.001  DISP         FREQUENCY COARSE/FINE  50Hz
 34.002  IEEE         [@5335][T0][I]
 34.003  ACC          50.00percent   0.001U
 34.004  MEME
 34.005  MEMC         percent        2.00U         50H
#!          Test Tol 2, Sys Tol 0.001, TUR 2000.000 (>= 4.00).
 35.001  DISP         Set the UUT as follows:
 35.001  DISP         RANGE  500
 35.001  DISP         FREQUENCY COARSE/FINE  500Hz
 35.002  IEEE         [@5335][T0][I]
 35.003  ACC          50.00percent   0.001U
 35.004  MEME
 35.005  MEMC         percent        2.00U         500H
#!          Test Tol 2, Sys Tol 0.001, TUR 2000.000 (>= 4.00).
 36.001  DISP         Set the UUT as follows:
 36.001  DISP         RANGE  5K
 36.001  DISP         FREQUENCY COARSE/FINE  5000Hz
 36.002  IEEE         [@5335][T0][I]
 36.003  ACC          50.00percent   0.001U
 36.004  MEME
 36.005  MEMC         percent        2.00U         5000H
#!          Test Tol 2, Sys Tol 0.001, TUR 2000.000 (>= 4.00).
 37.001  DISP         Set the UUT as follows:
 37.001  DISP         RANGE  50K
 37.001  DISP         FREQUENCY COARSE/FINE  50.00KHz
 37.002  IEEE         [@5335][T0][I]
 37.003  ACC          50.00percent   0.001U
 37.004  MEME
 37.005  MEMC         percent        2.00U         50kH
#!          Test Tol 2, Sys Tol 0.001, TUR 2000.000 (>= 4.00).
 38.001  DISP         Set the UUT as follows:
 38.001  DISP         RANGE  500K
 38.001  DISP         FREQUENCY COARSE/FINE  100.0KHz
 38.002  IEEE         [@5335][T0][I]
 38.003  ACC          50.00percent   0.001U
 38.004  MEME
 38.005  MEMC         percent        2.00U         100kH
#!          Test Tol 2, Sys Tol 0.001, TUR 2000.000 (>= 4.00).
 39.001  HEAD         {}
 39.002  JMP          40.001
 39.003  EVAL
 40.001  IEEE         [TERM LF]
 40.002  IEEE         [@5335]FN10;
 40.003  IEEE         [@5335][D2000][T0][I]
 40.004  MEM*         1000000000
 40.005  ACC          50.00nT        0.01U
 40.006  MEMC         0nT            -50U          risetime
#!          Test Tol 20, Sys Tol 0.01, TUR 2000.000 (>= 4.00).
 41.001  IEEE         [@5335]FN10;AS1;BS1;
 41.002  IEEE         [@5335][D3000][T0][I]
 41.003  MEM*         1000000000
 41.004  ACC          50.00nT        0.01U
 41.005  MEMC         0nT            -50U          falltime
#!          Test Tol 20, Sys Tol 0.01, TUR 2000.000 (>= 4.00).
 42.001  IEEE         [@34401]*RST[GTL]
 42.002  HEAD         {}
 42.003  END
#! T.U.R.s less than 4.00:                  0
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         0
#! T.U.R.s not computable at compile time:  8
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.